Roper® 70302 Pump Parts
M4 oversized-drive pin-joint family
ACCA Pumps supplies independently manufactured aftermarket replacement parts for supported Roper® progressive cavity pump configurations. Use the complete pump figure, serial number and construction when identifying parts.
Roper® 70302 Engineering Overview
Roper® identifies the 70302 configuration in its oversized-drive pin-joint cross-reference. The Roper® parts book associates this M-designation family with the corresponding L4 pumping-element references for rotor and stator selection.
Oversized Drive End
The M configuration uses a larger drive-end arrangement while retaining model-specific progressive-cavity pumping elements.
Pin-Joint Service
Inspect pins, bushings, connecting-rod interfaces, retaining hardware and drive-end wear components together.
Complete Figure Required
Rotor, stator and drive-end construction can vary. Confirm the complete pump identification before ordering.
Roper® 70302 Engineering Data
| Roper® Family | 70300 Series |
| Roper® Model | 70302 |
| M Designation | M4 |
| Pumping-Element References | 71202, 72202, 73202 |
| Joint Design | Pin joint / oversized-drive configuration |
| Related Roper® Resource | Roper® 70202 Pump Parts |
Before You Order Roper® 70302 Parts
Use the complete pump identification
Provide the full Roper® figure number, serial number, existing part number, material construction and elastomer. The M-series drive-end configuration and the pumping-element construction must both be confirmed.
Supported Roper® 70302 Pumping Elements
71202
1-stage pumping-element reference used with the M4 family.
72202
2-stage pumping-element reference used with the M4 family.
73202
3-stage pumping-element reference used with the M4 family.
Roper® 70302 Rotor & Stator Part Numbers
Roper®’s cross-reference directs M-designation pumps to the corresponding L-family rotor and stator references. The table below shows the standard plated-steel rotor and Buna 70 steel-tube stator references; alternate materials and elastomers use different part numbers.
| Pumping Element | Rotor Part Number | Stator Part Number | Reference Construction |
|---|---|---|---|
| 71202 | D96-4 | D95-25 | Standard plated-steel rotor / Buna 70 steel-tube stator reference |
| 72202 | D96-5 | D95-29 | Standard plated-steel rotor / Buna 70 steel-tube stator reference |
| 73202 | D96-6 | D95-33 | Standard plated-steel rotor / Buna 70 steel-tube stator reference |
Replacement Parts Available for Roper® 70302 Pumps
Rotors
Stage-specific rotor constructions for the applicable pumping element.
Stators
Buna, natural rubber, EPDM, Viton and other documented constructions where applicable.
Drive-End Components
Drive shafts, adapters, pins, bushings, connecting-rod components and retaining hardware for supported configurations.
Bearings & Seals
Bearings, lip seals, packing and related service components where applicable.
Packing Components
Packing sets, gland components, inserts and lantern rings for documented configurations.
Repair Hardware
Washers, spacers, retainers, keys and associated overhaul components.
Roper® 70302 Verified Drive-End Part Numbers
The following service parts are explicitly identified for the 7X302 configuration, or are listed inside its documented drive-end block in Roper®’s 2026 progressive-cavity parts book. Construction can change the applicable part number.
| Component | Roper® Part Number | Source Basis |
|---|---|---|
| Rotor head adapter — steel | D101-36 | Explicitly listed for 7X302 |
| Rotor head adapter — stainless | D101-32 | Explicitly listed for 7X302 |
| Drive pin — steel | D99-49 | Explicitly listed for 302 |
| Drive pin — stainless | D99-47 | Explicitly listed for 302 |
| Bushing — steel | G61-395 | Explicitly listed for 7X302 |
| Bushing | G61-393 | Listed in the 7X302 drive-end block |
Identification note
These references are for technical identification. Always verify the complete Roper® figure, material construction, serial number and existing component before ordering. ACCA does not reproduce Roper® list pricing on these pages.
Roper® 70302 Maintenance Recommendations
Inspect Joint Wear
Check pins, bushings and mating bores as a system.
Verify Drive-End Configuration
Do not substitute a standard-drive component where the oversized M drive end requires a different part.
Confirm Pumping Element
Match rotor and stator to the complete stage-specific pumping-element reference.
Progressive Cavity Engineering Note — Drive-End Loading
Progressive cavity pumps transmit hydraulic and rotor/stator loads through the connecting rod and drive end. An oversized drive-end configuration can provide additional mechanical capacity while retaining the pumping-element geometry appropriate to the service.
Frequently Asked Questions
What does Roper® 70302 correspond to?
The Roper® parts cross-reference identifies 70302 with the M4 oversized-drive family and directs rotor/stator selection to the related L4 pumping-element references.
Are the drive-end and pumping-element part numbers the same as the 70200 model?
No. Rotor and stator references can be shared through the documented cross-reference, while the oversized-drive configuration can require different drive-end components.
What information should I send for a quote?
Send the complete pump figure, serial number, existing part number, quantity, construction and photographs when available.
Can ACCA supply individual service components?
Yes. ACCA can support individual replacement components for applicable configurations after the installed pump is identified.
Related Progressive Cavity Pump Parts Resources
Roper® 70300 Parts
Return to the 70300 model selector.
Roper® 70202 Parts
View the related standard-drive pumping-element resource.
Roper® Pump Parts
Browse the complete Roper® parts hub.
Need Help Identifying Roper® 70302 Parts?
Send the complete Roper® figure number, serial number and existing part number when available.